Nor Nabilla Kadiman, Julie Elvyana Romli, Norhamidi Muhamad, Abu Bakar Sulong & Farhana Mohd Foudzi.  (2018).  Pengoptimuman parameter sonikasi dan pengacauan magnetik bagi mendapatkan penyerakan sebati komposit kuprum-grafin berdasarkan sifat morfologi.  - Sains Malaysiana.  . 

Mohd Ikram Ramli, Abu Bakar Sulong, Norhamidi Muhamad, Andanastuti Muchtar, Mohd Yusuf Zakaria.  (2018).  Pengoptimuman parameter pengacuan suntikan terhadap ketumpatan jasad anum untuk komposit aloi titanium-wolastonit.  - Sains Malaysiana.  . 

Mohd Khairul Fadzly Md Radzi, Norhamidi Muhamad, Majid Niaz Akhtar, Zakaria Razak & Farhana Mohd Foudzi.  (2018).  The effect of kenaf filler reinforcement on the mechanical and physical properties of injection moulded polypropylene composites.  - Sains Malaysiana.  . 

Najla Nazihah Mas'ood, Farhana Mohd Foudzi, Abu Bakar Sulong, Norhamidi Muhamad, Intan Fadhlina Mohamed, Farrahshaida Mohd Salleh, Ukwueze Bonaventure Emeka.  (2018).  Two component materials in powder metallurgy: a review paper focused on the processing technique applied in powder metallurgy.  - Jurnal Kejuruteraan.  23-31. 

Salleh F.M., Sulong A.B., Raza M.R., Muhamad N., Fhang L.T..  (2017).  Effects of space holder on fabrication of porous titanium alloy-hydroxyapatite composite through powder injection molding.  - Sains Malaysiana.  . 

Sarizal Md Ani, Andanastuti Muchtar, Norhamidi Muhamad & Jaharah A. Ghani.  (2017).  Kesan suhu pensinteran terhadap sifat mekanik dan mikrostruktur alumina zirkonia yang difabrikasi dengan kaedah pengacuan suntikan seramik.  - Sains Malaysiana.  1979-1986. 

Salleh, F.M., Sulong, A.B., Raza, M.R., Muhamad,N., Fhang, L.T.  (2017).  Effect of space holders on fabrication of porous titanium alloy-hydroxyapatite composite through powder injection molding.  - Sains Malaysiana.  1651-1657. 

Raza, M.R., Ahmad, F., Muhamad, N., Sulong, A.B., Omar, M.A., Akhtar, M.N., Aslam, M., Sherazi, I..  (2017).  Effects of debinding and sintering atmosphere on properties and corrosion resistance of powder injection molded 316 L - stainless steel.  - Sains Malaysiana.  285-293. 

Ukwueze Bonaventure Emeka, Abu Bakar Sulong, Norhamidi Muhamad, Zainuddin Sajuri & Farrahshaida Salleh.  (2017).  Two component injection moulding of bimaterial of stainless steel and yttria stabilized zirconia green part.  - Jurnal Kejuruteraan.  49-55. 

Tatt T.K., Muhamad N., Muchtar A., Sulong A.B., Cherng N.M..  (2016).  Influence of sintering parameters on the compressive yield strength of stainless steel foams produced by the space holder method.  - Sains Malaysiana.  653-658. 

J. Rajabi, A. B. Sulong, N. Muhamad, M. R. Raza.  (2015).  Powder compaction of bi-materials:stainless steel 316L and nanocrystaline yttria stabilized zirconia.  - Materials Technology.  313-320. 

Wong Yee Ning, Norhamidi Muhamad, Abu Bakar Sulong, Abdolali Fayyaz, Muhammad Rafi Raza.  (2015).  Effects of Vanadium Carbide on Sintered WC-10%Co Produced by Micro-powder Injection Molding.  - Sains Malaysiana.  1175-1181. 

Rajabi J., Zakaria H., Muhamad N., Sulong A.B., Fayyaz A..  (2015).  Fabrication of miniature parts using nano-sized powders and an environmentally friendly binder through micro powder injection molding.  - Microsystem Technologies.  1131-1136. 

Mohd Nizam Ab Rahman, Mahmood Doroodian, Yusniza Kamarulzaman, Norhamidi Muhamad.  (2015).  Designing and Validating a Model for Measuring Sustainability of Overall Innovation Capability of Small and Medium-sized Enterprises.  - Sustainability.  537-562. 

Amin S.Y.M., Muhamad N., Jamaludin K.R., Fayyaz A., Yunn H.S..  (2014).  Characterization of the feedstock properties of metal injection-molded WC-Co with palm stearin binder system.  - Sains Malaysiana.  123 - 128. 

M. I. Ramli, A. B. Sulong, N. Muhamad, A. Muchtar and A. Arifin.  (2014).  Stainless steel 316L hydroxyapatite composite via powder injection moulding: rheological and mechanical properties characterisation.  - Material Research Innovation.  100-104. 

Dedikarni Panuh, Andanastuti Muchtar, Norhamidi Muhamad, Edy Herianto Majlan, Wan Ramli Wan Daud.  (2014).  Elektrolit Dwi Lapisan Sm0.2Ce0.8O1.90 (SDC)/ Y0.25Bi0.75O1.5 (YSB) untuk Sel Fuel Oksida Pepejal Bersuhu Sederhana.  - Sains Malaysiana.  1769-1774. 

Sarizal Md Ani, Andanastuti Muchtar, Norhamidi Muhamad and Jaharah A. Ghani.  (2013).  Pencirian Keseragaman Campuran dan Sifat Reologi Serbuk Alumina-Zirkonia untuk Pengacuan Suntikan Seramik.  - Sains Malaysiana.  42(9):1311-1317. 

Nurul Akidah Baharuddin, Hamimah Abd. Rahman, Andanastuti Muchtar, Abu Bakar Sulong, Huda Abdullah.  (2013).  Development of lanthanum strontium cobalt ferrite composite cathodes for intermediate- low temperature solid oxide fuel cells.  - Journal of Zhejiang University-Science A.  11-24. 

Norita Hassan, Sahrim Ahmad, Norhamidi Muhamad, Mohd Afian Omar & Noor Azlina Hassan.  (2013).  Thermoplastic Natural Rubber (TPNR) As a Backbone Polymer for Metal Injection Molding.  - Sains Malaysiana.  42(12):1787-1791. 

Muhammad Ilman Hakimi Chua, Abu Bakar Sulong, Mohd Fazuri Abdullah & Norhamidi Muhamad.  (2013).  Optimization of Injection Molding and Solvent Debinding Parameters of Stainless Steel Powder (SS316L) Based Feedstock for Metal Injection Molding.  - Sains Malaysiana.  42(12):1743-1750. 

Javad Rajabi, Norhamidi Muhamad, Abu Bakar Sulong.  (2012).  Effect of nano-sized powders on powder injection molding: a review.  - Microsystem Technologies.  18(12):1941-1961. 

Hamimah Abd Rahman, Andanastuti Muchtar, Syaharizan Haron, Norhamidi Muhamad & Huda Abdullah.  (2012).  Kesan parameter pemprosesan dan bahan tambah terhadap pengendapan elektroforetik filem LSCF6428.  - Sains Malaysiana.  41(2): 237-244. 

Dedikarni Panuh, Andanastuti Muchtar*, Norhamidi Muhamad & Wan Ramli Wan Daud.  (2012).  Kesan rawatan haba terhadap mikrostruktur katod berliang Ag2O3-Bi2O3 di atas substrat keluli kalis karat yang disediakan dengan kaedah pengecatan sluri.  - Sains Malaysiana.  41(1): 121-127. 

Jarot Raharjo, Andanastuti Muchtar*, Wan Ramli Wan Daud, Norhamidi Muhamad & Edy Herianto Majlan.  (2012).  Pencirian fizikal dan terma komposit seramik elektrolit SDC-(Li/Na)2CO3 (Physical and thermal characterisations of SDC-(Li/Na)2CO3 electrolyte ceramic composites).  - Sains Malaysiana.  41(1): 95-102. 

Mohd H.I. Ibrahim, Norhamidi Muhamad, Abu B. Sulong, Khairur R. Jamaludin, Nor H.M. Nor and Sufizar Ahmad.  (2011).  Optimization of micro metal injection molding with multiple performance characteristics using grey relational grade.  - Chiang Mai Journal of Science.  38(2):231-241. 

Ahmad, S; Muhamad, N; Muchtar, A; Sahari, J; Jamaludin, KR; Ibrahim, MHI; Nor, NHM; Murtadhahadi.  (2010).  Characterisation of Titanium Foams Sintered at Different Temperatures Prepared by the Slurry Method.  - Sains Malaysiana.  39(1):77-82. 

A.Y. Musa, A. A. H. Kadhum, M. S. Takriff, A. R. Daud, S. K. Kamarudin and N. Muhamad.  (2010).  Corrosion inhibitive property of 4-amino-5-phenyl-4H-1,2,4-triazole-3-thiol for mild steel corrosion in 1.0M hydrochloric acid.  - Corrosion Engineering, Science and Technology.  45(2):163-168. 

Khairur Rijal Jamaludin, Norhamidi Muhamad, Mohd Nizam Ab. Rahman, Sri Yulis M. Amin, Sufizar Ahmad, Mohd Halim Irwan Ibrahim, Murtadhahadi.  (2009).  Prestasi Penyahikatan Pelarut dengan Menggunakan Kaedah Reka Bentuk Eksperimen.  - Sains Malaysiana.  38(6):883-888. 

Ahmed. Y. Musa, Abdul Amir H. Kadhum, Abu Bakar Mohamad, Abdul Razak Daud, Mhd Sobri Takriff, Siti Kartom Kamaruddin & Norhamidi Muhamad.  (2009).  Stability of Layer Forming for Corrosion Inhibitor on mild Steel surface under hydrodynamic condictions.  - Internationa Journal of Electrochemical Science.  4(5):707-716 . 

Lily Amelia, D.A. Wahab, C.H. Che Haron, N. Muhamad, C.H. Azhari.  (2009).  Initiating automotive component reuse in Malaysia.  - Journal of Cleaner Production.  17(17):1572-1579. 

Sulong A.B., Muhamad N., Ghazali M.J., Jaharah A.G., Tan S.H., Park J.H..  (2009).  Functionalized mwcnts reinforced polyetehylene fiber composite: Mechanical strength characterization.  - International Journal of Modern Physics B.  23(6-7):1419-1424. 

Jamaludin, KR; Muhamad, N; Rahman, MNA; Ahmad, S; Ibrahim, MHI; Nor, NHM.  (2009).  Optimizing the Injection Parameter of Water Atomised SS316L Powder with Design of Experiment Method for Best Sintered Density.  - Chiang Mai Journal of Science.  36(3):349-358.