Penerbitan WOS

Che Hassan Che Haron, Jaharah A. Ghani, Mummar Faiq Azhar, Nurul Hayati Abdul Halim.  (2019).  Wear mechanisms of coated tungsten carbide when machining Inconel 718 under cryogenic and dry conditions.  - Jurnal Tribologi.  108-116. 

Haniff Abdul Rahman, Jaharah A. Ghani, Wan Mohd Faizal Wan Mahmood, Mohammad Rasidi Mohammad Rasani,.  (2019).  Computational fluid dynamic study on the tribological performance of dimple-textured surface fabricated using the turning process.  - Industrial Lubrication and Tribology.  594-602. 

Shalina Sheik Muhamad, Jaharah A. Ghani, Afifah Juri, Che Hassan Che Haron.  (2019).  Dry and cryogenic milling of AISI 4340 alloy steel.  - Jurnal Tribologi.  1-12. 

M. Rizal, J.A. Ghani, Husni, Husaini.  (2018).  Design and construction of a strain gauge-based dynamometer for a 3-axis cutting force measurement in turning process.  - Journal of Mechanical Engineering and Sciences. 

H. Azmi, C.H. Che Haron, J.A. Ghani & M. Suhaily.  (2018).  Pembandingan kesan faktor pelekangan (Fd) ke atas bahan komposit plastik bertetulang ekaarah dan bertenun semasa proses pemesinan kisar.  - Sains Malaysiana. 

Kamal Othman, Jaharah A. Ghani, Mohd Shahfizal Ruslan, Mohd Shahir Kassim.  (2018).  Surface roughness of hypereutectic Al-Si A390 in high speed milling.  - Jurnal Tribologi.  42-50. 

Aminul Islam, A.K.M., Yaakob, Z., Anuar, N., Primandari, S.R.P., Ghani, J.A..  (2017).  Properties of jatropha hybrid seed oil and its suitability as biodiesel feedstock.  - Energy Sources, Part A: Recovery, Utilization and Environmental Effects.  1707-1717. 

A. Shukriah, M. D. Baba, A. G. Jaharah.  (2017).  Prevalence and factors contributing to musculoskeletal disorder among garage worker in Malaysia.  - Journal of Fundamental and Applied Sciences.  1070-1079. 

A. Shukriah, M. D. Baba, and A.G. Jaharah.  (2017).  Reba evaluation on garage worker: A case study.  - Journal of Fundamental and Applied Sciences.  1080-1086. 

Mohd Nor Azam Mohd Dali, Jaharah A. Ghani, Che Hassan Che Haron, Sharudin Hassan.  (2017).  Fabrication of dimple structured surface of A390 Al-Si alloy using turning process.  - Industrial Lubrication and Tribology.  348-354. 

Sarizal Md Ani, Andanastuti Muchtar, Norhamidi Muhamad & Jaharah A. Ghani.  (2017).  Kesan suhu pensinteran terhadap sifat mekanik dan mikrostruktur alumina zirkonia yang difabrikasi dengan kaedah pengacuan suntikan seramik.  - Sains Malaysiana.  1979-1986. 

Jaharah A. Ghani, Che Hassan Che Haron, Hazreen Othman, Natasha A. Raof.  (2017).  Chip formation in turning S45C medium carbon steel in cryogenic conditions.  - Jurnal Tribologi.  1-9. 

Mohd Nor Azam Bin Mohd Dali, Jaharah A. Ghani, Che Hassan Che Haron, Sharudin Bin Hassan.  (2016).  FEM simulation for determining suitable parameters for dimple structure fabrication in turning process.  - International Journal of Materials & Product Technology.  218-230. 

Sukadarin E.H., Deros B.M., Ghani J.A., Mohd Nawi N.S., Ismail A.R..  (2016).  Postural assessment in pen-and-paper-based observational methods and their associated health effects: a review.  - International Journal of Occupational Safety and Ergonomics.  389-398. 

Jaharah A. Ghani, A.R. Natasha, C.H. Che Hassan and J. Syarif.  (2016).  TRIZ approach for machining process innovation in cryogenic environment.  - International Journal of Materials & Product Technology.  286-297. 

A.K.M. Aminul Islam, Nurina Anuar, Zahira Yaakob, Jaharah A. Ghani & Mohamad Osman.  (2015).  Diallel Analysis for Seed Yield and Related Traits in an Energy Crop Jatropha curcas.  - Sains Malaysiana.  979-986. 

A.K.M. Aminul Islam, Nurina Anuar, Zahira Yaakob & Jaharah A. Ghani.  (2015).  Germination Behaviour of 6 6 Diallel Hybrids of an Energy Crop Jatropha curcas L.  - Sains Malaysiana.  1275-1281. 

M.A. Sulaiman, C.H. Che Haron, J.A. Ghani & M.S. Kasim.  (2014).  Effect of High-speed Parameters on Uncoated Carbide Tool in Finish Turning Titanium Ti-6Al-4V ELI.  - Sains Malaysiana.  43(1): 111-116. 

MS Kasim, CH Che Haron, JA Ghani, MA Azam, Rizamshah, MA Md Ali and MS A Aziz.  (2014).  The influence of cutting parameter on heat generation in high-speed milling Inconel 718 under MQL condition.  - Journal of Scientific & Industrial Research.  73:62-65. 

Abdullah Ismail, Jaharah A. Ghani, Mohd Nizam Ab Rahman, Baba Md Deros, and Che Hassan Che Haron.  (2014).  Application of Lean Six Sigma Tools for Cycle Time Reduction in Manufacturing: Case Study in Biopharmaceutical Industry.  - Arabian Journal for Science and Engineering.  1449-1463. 

Salah Al-Zubaidi, Jaharah Abdul Ghani, Che Hassan Che Haron.  (2014).  Prediction of Tool Life when End Milling of Ti6Al4V Alloy Using Hybrid Learning System.  - Arabian Journal for Science And Engineering.  39(6):5095-5111. 

M.S. Kasim, C.H. Che Haron, J.A. Ghani, A.I. Gusri, M.Z.A. Yazid & M.A. Sulaiman.  (2013).  Tool Life of TiAlN PVD Coated Carbide Tool in High-speed End Milling of Untreated Inconel 718 under Minimum Quantity Lubrication Condition.  - Sains Malaysiana.  42(12):1721-1726. 

Sarizal Md Ani, Andanastuti Muchtar, Norhamidi Muhamad and Jaharah A. Ghani.  (2013).  Pencirian Keseragaman Campuran dan Sifat Reologi Serbuk Alumina-Zirkonia untuk Pengacuan Suntikan Seramik.  - Sains Malaysiana.  42(9):1311-1317. 

Jaharah A. Ghani, Yeong Shoot Kian, Stephanie Tan Chia Ven, Zahira Yaakob, and Che Hassan Che Haron.  (2012).  Performance of Biodegradable Palm Oil Coolant in Machining Process.  - Journal of Biobased Materials and Bioenergy.  6:1-4. 

Afifi Zainal, Zahira Yaakob, Mohd Sobri Takriff, Renganathan Rajkumar, and Jaharah Abdul Ghani.  (2012).  Phycoremediation in Anaerobically Digested Palm Oil Mill Effluent Using Cyanobacterium, Spirulina platensis.  - Journal of Biobased Materials and Bioenergy.  6:1-6. 

Jaharah A. Ghani, Poh Siang Jye, Che Hassan Che Haron, Muhammad Rizal, Mohd Zaki Nuawi.  (2012).  Determination of sensor location for cutting tool deflection using finite element method simulation.  - Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science.  226(9):2373-2377. 

Rizauddin Ramli, Dzuraidah Abd Wahab, Jaharah Abd Ghani and Raime M. Zain.  (2012).  A comparison of lifted lead defect inspection system for surface mount technology.  - Journal of Scientific and Industrial Research.  71(5):330-333. 

Aminah Ishak, Jaharah A. Ghani, Che Hassan Che Haron.  (2012).  Penentuan Faktor yang Mempengaruhi Daya dan Taburan Tegasan Semasa Pemesinan Besi Tuangan Mulur (FCD 500) Secara Simulasi.  - Sains Malaysiana.  41(12):1605-1612.